Products by Series

Insert Series

Style FIVStyle FIV

Style F1, F6, FP (FIV)

The Flange Insert Valve can be installed in any ANSI class 150, 300, or 600 flanged connection in the system, horizontally or vertically with no alterations to existing pipe necessary. Simply spread a flanged joint, insert the valve, and tighten the bolts. View More
Style LPI

Style LP (LPI)

The Lined Pipe Insert check valve is designed to fit between two flanges on most lined pipe systems.  No gaskets are required, just spread the flanges, center the valve, and bolt the flanges.  View More


Style SC (SCV)

The Sanitary Cartridge Valve is a 316 stainless steel check valve for use in new or existing sanitary systems.  The SCV design seals on the ID of sanitary ferrules with replaceable food grade seals.  View More

 

Style 3SC

Style 3S (3SC)

The 3-A Sanitary Check Valve is an all  316/316L stainless steel check valve for use in new or existing sanitary systems.  The compact 3S design fits inside a single set of ferrules with 3-A specified materials (standard is EPDM), and requires no additional space in the line.  The valve is designed to be easily disassembled and spare parts are available.   View More

Style SIV

Style CB, TC (SIV)

The Sanitary Insert Valve is an all fluoropolymer (PTFE/FEP/PFA), check valve with a 316 stainless steel spring (which can be FEP encapsulated) for use in new or existing sanitary systems.  The valve is designed to fit into grooved end clamp type fittings and replaces the gasket normally used with these fittings.  View More

Style UIV

Style UV (UIV)

The Union Insert Valve is designed to be inserted into most ground joint unions.  It provides the most simple and economical way to install a check valve into a system.  View More

Style SSI 

Style SI (SSI)

The Straight Sided Insert valve is a thread-less check valve designed for use in any cavity where a check valve is needed and threads are not desired.  View More

Style GPI

Style GP (GPI)

The Glass Pipe Insert check valve an all fluoropolymer (PTFE/FEP/PFA) check valve with a FEP encapsulated spring.  This check valve is used in systems that utilize glass pipe and installs between connecting flanges where a gasket would normally be located.   View More
Back to Top

Housed Series

Style UN-3 U1-Universal High U3-Universal Low

Styles U3 (UN-3) and U1 (UN-10)

The Universal Low (to 3,000 psig) and High (to 10,000 psig) pressure check valves have a single piece body construction machined from bar stock.  These economical valves are designed for maximum flow with minimum pressure drop. View More UN-3 or View More UN-10.

 

Style UN-SW

Style US (UN-SW)

The Universal Socket Weld check valve is designed for use in applications where weld joints are required. The housed design of the UN-SW allows for minimum pressure drop when a light spring setting is used.  View More

 

Style CON

Style CN (CON)

The Connector check valve is designed for use in applications where male pipe threads are required.  The hex nipple or connector housing design allows for ease in installation either as a check valve, vacuum breaker or low-pressure relief valve.  View More

 

Style BU

Style BU (BU)

The Bushing check valve is compactly housed in a common reducing coupling.  It's size makes it convenient for use as a vacuum breaker or low-pressure relief valve.  View More

Style HVFD

Style HV (HVFD)

The Horizontal/Vertical Flanged and Drilled Valve is a one-piece cast body valve with ANSI/ASME B16.5 Class 150 flanged ends.  It is available in ANSI 150 only.  These valves are designed for use with mating ANSI class 150 flanges for maximum flow with minimum pressure drop.  View More

Style HVFD-T

Style HT (HVFD-T)

The Horizontal/Vertical Flanged & Drilled-Fluoropolymer (PTFE) Lined check valve is a one-piece cast body valve with ANSI/ASME B16.5 Class 150 flanged ends.  It has a solid one-piece PTFE liner that extends over the raised face portion of the flange face to serve as the gasket.  All wetted parts are fluoropolymer (PTFE/FEP/PFA) including the FEP encapsulated Stainless Steel spring.  View More

Back to Top

Mini-Check Series

Style MCV

Styles M1 - M8 (MCV)

The Mini-Check Valve is a three-piece construction check valve. The MCV is designed to work well in smaller pipe and/or tubing applications.  Its three-piece design allows for many different end connections with NPT on both ends or with NPT on one end and tubing on the other.  View More

 

Back to Top

Tubing Series

Style TCV

Style TCV (TV)

The Tubing Check Valve is a three-piece construction check valve designed for use with straight metal tube.  The TCV is furnished complete with ferrules and nuts for compression tube connections. The housed design of the TCV allows for minimum pressure drop when a light spring setting is used.  View More

 

Tubing Check Valve by Check-All

Style TF (TCV-F)

The Tubing Check Valve-Flared is a three-piece construction check valve with 37oflared ends that conform to J. I. C. and SAE Hydraulic Standards. The housed design allows for minimal pressure drop when a light spring setting is used.  View More

 

Back to Top

Custom Series

Style CAV

Style CAV

The CAV series of valves are not catalog items but rather are custom designed and tailored to meet customer specific connections or valve configurations.  If you have a check valve application where our standard catalog items do not quite match what you are looking for, contact our sales department to discuss your specific needs.  View More