Sanitary Insert Valve Style- CB, TC

Member of the Insert Series

Click To Enlarge

Valve shown in ferrules.
Ferrules and clamp not included.
×

Sanitary Insert Valve Style- CB, TC

Valve shown in ferrules.
Ferrules and clamp not included.

For over 50 years, the compact, fluoropolymer (PTFE/FEP/PFA), Sanitary Insert Valve has been used as the most economical solution to providing a check valve in a new or existing sanitary piping system. This valve style is designed to fit into grooved-end clamp-type fittings. Since the Sanitary Insert Valve replaces the gasket normally used with clamp joints, no extra space is required to accommodate the valve.

Two different types of Sanitary Insert Valves are available. They are distinguished by the following designations in their part numbers:

TC - Designates Tri-Clamp® fittings manufactured by Alfa Laval Inc. as well as Waukesha Cherry-Burrell® S-Line Series of fittings.

CB - Designates the Waukesha Cherry-Burrell® Q-Line Series of fittings.
NOTE: Sanitary Insert Valve Types TC and CB are NOT interchangeable!

PED Compliance Statement: Due to the unique "insert" design of our 3S, SC, CB, TC, SI, & UV, style check valves, they do not constitute an "identifiable pressure bearing housing" as defined in PED Guideline 1/8. These styles must be installed into either ferrules or fittings to create a pressure bearing housing. Instead, they are classified as "components of pressure equipment" as defined in PED Guideline 1/8. As a result, these valves can be sold in the European Community and no CE Mark is required.

In addition applicaitons where the maximum allowed oerating pressure is 0.5 bar (7.2 psi) or less, do not fall under the PED, regardless of the valve style.

(View Similar Products)

NOTES (DIMENSIONS TABLE)
*Due to molding process, orifice may vary.
**Maximum nominal dimension for a fully open valve with no spring.
Consult factory for more information.

View SIV Dimensions in PDF format
Line Size Size Code TC - Alfa Laval Inc.
Waukesha Cherry-Burrell®
S-Line		 CB-Waukesha Cherry-Burrell®
Q Line Only		 Orifice
Dia.*
A
B
C
D**
E
A
B
C
D**
E
3/4 F 0.590 55/64 0.55 0.63 0.800 - - - - - 0.348
1 H 0.855 2 0.55 0.70 1.718 0.850 1-3/4 0.55 0.70 1.437 0.464
1-1/2 J 1.345 2 0.60 0.98 1.718 1.350 2 0.60 0.98 1.716 0.890
2 K 1.845 2-1/2 0.57 1.12 2.218 1.850 2-1/2 0.57 1.12 2.247 1.135
2-1/2 L 2.355 3 0.60 0.98 2.781 2.250 3-1/4 0.60 0.98 2.841 1.385
3 M 2.845 3-1/2 0.64 1.59 3.281 2.852 3-55/64 0.61 1.58 3.372 2.025
4 N 3.806 4-5/8 0.78 1.90 4.344 3.800 4-55/64 0.73 1.89 4.372 2.560
  • PTFE (TF)
    		•
    Body Material Line Size Non-Shock Pressure-Temperature Rating
    PTFE (TF) 3/4"- 2" 55 PSIG @ 100 °F
    2-1/2 " - 4" 20 PSIG @ 100 °F

    Seat material and spring material selection may limit the recommended service temperature.
    See seat ratings, spring ratings, and body material ratings for their respective recommended service temperatures.
    Consult the factory for reduced P-T rating above 100 °F. Standard spring material is 316 Stainless Steel.

    Size Cv
    3/4 2.4
    1 4.6
    1-1/2 9.5
    2 20.9
    2-1/2 37.0
    3 76.0
    4 141

    P
    R
    E
    S
    S
    U
    R
    E

    D
    R
    O
    P

    P
    S
    I

    FOR WATER AT 72°F

    WATER FLOWRATE - GPM

    Note: All flow curves and Cv values presume the valves are fully open with 1/2 PSI cracking pressure springs. Consult the factory for more information.
    SIZE PTFE
    3/4 0.2 oz.
    1 0.6 oz.
    1-1/2 1.1 oz.
    2 1.8 oz.
    2-1/2 2.3 oz.
    3 5.1 oz.
    4 11.2 oz.
    Valve weights are approximate.
    Valve Style Size Range Body Materials Other Options Allowable Seat Materials Other Options Standard Cracking Pressures Other Options More Info. Standard Spring Material More Info.
    SIV 3/4" - 2" PTFE AFLAS®
    Buna-N
    FDA AFLAS®
    FDA Buna-N
    EPDM/FDA EPDM
    		 FDA Viton®
    Kalrez®
    "Metal to Metal"
    Neoprene
    Viton®
    		 1/8 PSI
    1/2 PSI
    1.5 PSI
    3.5 PSI    		 316 SS
    SIV 2-1/2" - 4" PTFE AFLAS®
    Buna-N
    FDA AFLAS®
    FDA Buna-N
    EPDM/FDA EPDM
    		 FDA Viton®
    Kalrez®
    "Metal to Metal"
    Neoprene
    Viton®    		 1/8 PSI
    1/2 PSI
    1.5 PSI
    		 316 SS

    About Us • Trademarks • Privacy Policy • Terms of Use • Contact Us

    ©2016 Check-All Valve Mfg., Co. All Rights Reserved